Pollutants removal and simulation model of combined membrane process for wastewater treatment and reuse in submarine cabin for long voyage

A laboratory scale test was conducted in a combined membrane process (CMP) with a capacity of 2.91 m3/d for 240 d to treat the mixed wastewater of humidity condensate, hygiene wastewater and urine in submarine cabin during prolonged voyage. Removal performance of chemical oxygen demand (COD), ammonia nitrogen (NH4 +-N), turbidity and anionic surfactants (LAS) was investigated under di erent conditions. It was observed that the e uent COD, NH4 +-N, turbidity and LAS flocculated in ranges of 0.19–0.85 mg/L, 0.03–0.18 mg/L, 0.0–0.15 NTU and 0.0–0.05 mg/L, respectively in spite of considerable fluctuation in corresponding influent of 2120–5350 mg/L, 79.5–129.3 mg/L, 110–181.1NTU and 4.9–5.4 mg/L. The e uent quality of the CMP could meet the requirements of mechanical water and hygiene water according to the class I water quality standards in China (GB3838-2002). The removal rates of COD, NH4 +-N, turbidity and LAS removed in the MBR were more than 90%, which indicated that biodegradation is indispensable and plays a major role in the wastewater treatment and reuse. A model, built on the back propagation neural network (BPNN) theory, was developed for the simulation of CMP and produced high reliability. The average error of COD and NH4 +-N was 5.14% and 6.20%, respectively, and the root mean squared error of turbidity and LAS was 2.76% and 1.41%, respectively. The results indicated that the model well fitted the laboratory data, and was able to simulate the removal of COD, NH4 +-N, turbidity and LAS. It also suggested that the model proposed could reflect and manage the operation of CMP for the treatment of the mixed wastewaters in submarine.     

离子膜辅助电催化氧化法预处理焦化废水的研究

焦化废水是属有毒有害、难降解的有机废水,常规的生物处理工艺对其去除效果不甚理想,从而导致出水中难降解污染物含量较高,COD和NH3-N不能达标。论文针对焦化废水的水质特点,采用离子膜电解技术进行预处理。对焦化废水中主要污染物苯酚降解效果的几种因素进行了研究,得出了苯酚降解的最佳工艺条件并在此工艺参数下,对模拟焦化废水电解2.5h,苯酚、COD的去除率分别为84%,45%,氨氮去除率和回收率别为99.5%和96.5%,总能耗27kwh/m3,可以为后续生化处理大大减轻负担,采用该方法作为焦化废水的预处理手段比较经济合理。     

A／O膜生物反应器处理生活污水的试验研究

根据传统脱氮除磷工艺——好氧硝化缺氧反硝化原理,设计并制作了一种分置式A／O膜生物反应器,并且对其曝气方式进行合理改进,利用射流曝气强大的复氧能力和混合能力,使好氧区的泥水能更加均匀地混合以及能提供充足的氧气。并就其对生活污水中污染物的去除效果及其机制进行了试验研究,结果表明,该改进后的膜生物反应器在连续运行60天内,系统不排泥,水力停留时间为16h时,对COD、总氮、氨氮有良好的去除效果,平均去除率分别达到94％,70．7％,98．4％,出水CODCr、总氮、氨氮浓度分别在50mg／L,15mg／L,1mg／L以下。     

Selective sorption of perfluorooctane sulfonate on molecularly imprinted polymer adsorbents

Perfluorooctane sulfonate (PFOS), as a potential persistent organic pollutant, has been widely detected in water environments, and has become a great concern in recent years. PFOS is very stable and difficult to decompose using conventional techniques. Sorption may be an attractive method to remove it from water. In this study, the molecularly imprinted polymer (MIP) adsorbents were prepared through the polymerization of 4-vinylpyridine under different preparation conditions in order to remove perfluorooctane sulfonate (PFOS) from water. The MIP adsorbents using perfluorooctanoic acid (PFOA) as the template had good imprinting effects and could selectively remove PFOS from aqueous solution. The sorption behaviors including sorption kinetics, isotherms, and effect of pH, salt, and competitive anions were investigated. Experimental results showed that the sorption of PFOS on the MIP adsorbents was very fast, pH-dependent, and highly selective. The achieved fast sorption equilibrium within 1 h was attributed to the surface sorption on the fine adsorbents. The sorption isotherms showed that the sorption selectivity of PFOS on the MIP adsorbents decreased at high PFOS concentrations, which may be due to the double-layer sorption and the formation of PFOS micelles on the sorbent surface. The sorption of PFOS on the MIP adsorbents was mainly dominated by the electrostatic interaction between the protonated vinylpyridine on the adsorbent surface and the anionic PFOS. The prepared MIP adsorbents can potentially be applied in water and wastewater treatment for selective removal of PFOS.     

胞外聚合物对MBR中改性无纺布过滤性能的影响

采用统计分析方法研究了胞外聚合物(extra-cellular polymeric sub6tances, EPS)对浸渍式膜生物反应器(submerged membrane bioreactor, SMBR)中聚乙烯醇改性聚丙烯无纺布过滤性能的影响.结果表明,无纺布膜组件表面污泥的溶解性EPS(soluble EPS, EPSs)、EPSs,组成(protein/carbohydrate, P/C)以及相对疏水性(relative hydrophobicity, RH)对膜的过滤性能有显著影响,与膜污染阻力的皮尔逊相关系数(rp)分别为:0.868、0.840、0.890;改性无纺布膜组件能有效抑制EPSs,的吸附、降低EPSs组分中P/C的比率、减少活性污泥的沉积.表明聚丙烯无纺布通过亲水改性后,过滤性能得到明显改善,表现出一定的耐污染性.     

萃取膜生物反应器处理苯酚废水的试验研究

从经过驯化的活性污泥中筛选出苯酚降解菌.制备成菌悬液,对比活性污泥体系和菌悬液体系的萃取膜生物反应器(EMB)对苯酚废水的处理效果,考察了料液苯酚浓度、反应器温度等因素对膜萃取速率及生物降解效果的影响.结果表明,通过以苯酚为唯一碳源,逐渐提高苯酚浓度的方法对活性污泥进行驯化.当进水苯酚浓度为700 mg·L-1时,苯酚去除率达99%以上;适当提高反应器温度和料液初始浓度有利于提高膜萃取速率;当初始料液苯酚浓度为2000 mg·L-1时,膜萃取速率高于生物降解速率,生物相中产生苯酚积累;菌悬液体系EMB的生物膜厚度明显小于活性污泥体系,且水力反冲洗可有效控制生物膜厚度.对苯酚生物降解产物的GC-MS分析结果表明,苯酚的生物降解较彻底,基本无苯酚中间产物的残留.     

曝气强度对膜生物反应器污泥混合液可滤性的影响

主要研究了曝气强度对膜生物反应器(MBR)膜污染的影响.2套MBR采用恒流出水模式连续运行60 d,曝气强度分别为500及100 L/h,应用死端过滤装置来检测不同阶段污泥混合液的可滤性.实验中对不同曝气强度下的溶解性微生物代谢产物(SMP)分子质量分布、颗粒粒径分布、胞外聚合物(EPS)含量进行了测定.结果表明,过高的曝气强度将恶化污泥混合液的可滤性,增加了膜污染速率.进一步研究表明,曝气强度的增加导致了污泥混合液上清液中相对分子质量>10000的SMP浓度的增加,此部分大分子有机物浓度直接影响了污泥混合液的可滤性.过高的曝气强度也导致了污泥絮体中1～10μm细小颗粒和EPS含量的增加.     

氢氧化镁-壳聚糖复合絮凝剂对印染废水的脱色研究

使印染废水脱色是废水处理的重要问题,利用无枳／有机复合絮凝剂可取得优良的脱色效果。采用氢氧化镁一壳聚糖复合絮凝剂对印染废水进行脱色处理,研究了pH值、壳聚糖投加量、复合絮凝剂加入量等对脱色效果的影响。结果表明氢氧化镁一壳聚糖复合絮凝剂比单独使用氢氧化镁絮凝剂脱色效果好。壳聚糖是一种天然高分子化合物,是甲壳素的脱乙基产物。来源丰富,且具有无毒副作用、易降解等优点。利用壳聚糖作为复配剂制备的复合絮凝减少了镁盐的使用量,有效降低了废水处理成本,避免引起二次污染。     

好氧颗粒污泥膜生物反应器污泥性状研究

采用厌氧-好氧运行方式的颗粒污泥膜生物反应器（GMBR）,连续运行近120　d表现出良好的有机物去除及同步硝化反硝化能力.对GMBR中污泥粒径分布变化研究表明,GMBR中污泥浓度的增加主要是由于粒径0.18～0.45　mm的小颗粒污泥及小于0.18　mm的絮状污泥的增加造成的,粒径大于0.45　mm的颗粒污泥能够基本稳定维持其颗粒形态,反应器运行末期,GMBR中颗粒污泥（粒径大于0.18　mm的污泥）含量稳定在污泥总量的60％～65％以上.污泥表面电荷量随着污泥组成形态的变化电负性逐渐增加,80　d后稳定在-0.42～-0.80　meq·g^-1之间.污泥表面电荷的负电性增加主要是由小于0.45　mm的污泥造成的,其中小于0.18　mm的絮状污泥对其影响最大.并且,污泥粒径越大污泥表面负电荷量越少,两者具有较好的线性关系.另外,GMBR中SVI稳定在60～90 mL/g之间,并且随着污泥表面电荷负电性的增加污泥SVI值增加,两者之间具有一定的相关性.     

超滤处理洗涤污水循环利用的中试研究

采用不同材质国产超滤膜聚丙烯（PP）、聚丙烯腈（PAN）和聚砜（PS）,进行了洗涤污水处理循环利用的现场中试研究.结合超滤工艺出水水质和膜污染分析,3种膜材质中PAN膜较优,有效去除了水中浊度、悬浮物、油脂等污染物,一定程度保留了游离阴离子表面活性剂（LAS）,长期循环洗涤对衣物的白度无不良影响.根据相关性分析,超滤出水较高COD值很大程度上是由水中LAS引起的.超滤膜对细菌、大肠菌群的去除率较低,出水通过紫外消毒,当紫外线密度≥3?750 J/m²时,微生物水平能够达到国家饮用水水质标准.根据不同水力反冲洗条件下膜渗透通量和净产水量比较,PAN膜最佳水力反冲洗条件为0.5 h反冲洗2 min.长期运行时超滤膜化学清洗方法采用碱洗法方便有效.